Modification Motor Since its launch in 2003, Yamaha Mio successfully held national matic market with circulation exceeding 700ribu. Originally predicted to be iconic motorcycle women, but also preferred not less than 50 per cent of men. Ease of operation, small dimensions and shape are up to date so the key to success matic 113.7 cc. In spite of it all, a variety of daily tips can be acted dewe loh. Listen yuk A-Z tips journal:
1. Renewal Age Wear V-BELT: V-Belt Indeed routine must be changed every 15 thousand miles use, but not uncommon before the number, V-Belt had already eroded or replaced because a lot of stretching caused by negligent care. It would be wise if you regularly clean the filter filters dust cover CVT. Only by cleaning gasoline, dirt dust that often lead V-Belt slippage can be removed quickly.
2. Check Oil-Water Content Filter carburetor Box: Each box filter carburetor Mio always include water and oil detector. Through this transparent detector made of rubber, you can check whether your Mio carburetor filter box filled with oil or water. If the answer is yes, immediately disassemble and clean the carburetor filter box. Cost and time for operation: Rp. 5 Thousand & 15 minutes Equipment: Gasoline, Key Sok Size 8
3. Routine Oil Change Transmission CVT: In the CVT transmission, there is also the teeth. To be durable and function properly, you must routinely mileage reimbursement every 10 thousand miles. Apparently the oil does not have a special CVT oil anyway, pake aja SAE 40 oil is also used as an engine lubricating oil. just as much as 100cc. Cost | Old Workmanship: Rp. 5-10 Thousand | 45 minutes Equipment: Gasoline, Oil, Oben (+) and Key Pas 10
4. Routine Check Avoid Corrosion Aki: Aki has a dominant role for electrical support, especially ignition engine with the help of an electric starter. Frequently check the condition of the battery. ranging from water level to the condition of bolt + / - his. If careless, Koros Host kutub2 filled crust. If not cleaned regularly crust with airpanas. Cost | Old Workmanship: Rp. 5 Thousand | 10 min Equipment: Screwdriver (+) and (-), hot water, and brush
5. Extend Hole Irrigation Storage: Storage Mio has two small holes in the corner-corner. This hole is a hole that functions to irrigation drainage water trapped in the trunk. In order to get more leverage, expand the size of the drill hole with the bolt 12. Cost | Old Workmanship: - | 5 minutes Equipment: Electric Drill
6. Easy Set carburetor: Position carburetor Mio hide the body, precisely under the trunk side body surrounded and under seat cover. Well practical way to enlarge / shrink RPM rotation through the carburetor, simply open the seat and open the rubber cover at the base of the trunk length. Adjust the carburetor through the hole with a screwdriver doang capital. Cost | Old Workmanship: - | 5 minutes Equipment: Screwdriver (+)
7. Keep Cop Busi Water Proofing: Position Busi Mio including hard to reach, but it is also the position just behind the hole anginunder seat cover. Automatic prone to water from the hole. That's why the cop made watertight plug equipped with rubber lips. In order to be okay, do not replace it with any cop, in addition to maintaining kekedapannya, use the help of a topical sealer around the cop lip plugs. Cost | Old Workmanship: 10 Thousand | 10 min Equipment: Glue Sealer, Screwdriver (+)
8. Save the Engine Number: Number Mio machine is on the wall above the block CVT, but unfortunately its position right on the edge of the tire wall. This area is often forged Automatic aik water dirt and dust. In order not easily affected by corrosion damaged, immediately secure with lacquer coating Charges | time for operation: 15-25ribu | 5 minutes Equipment: clear spray paint, pen, brush or spray gun, varnish
9. Treat Black Plastic Coverage: Orsi her, Mio does not entirely cover using plastic-coated paint. Some of them use a black plastic material such as back deck cover, foot board to the under seat cover. The problem part is especially difficult to clean scratched frequency. Tips potent cheap cleanses and discolor surfaces is back with the help of shoe polish. Cost | Old Workmanship: 5-10 Thousand | 30 minutes Equipment: Shoe black shoes, shoe polish brush, cleaning wipes
10. Banish Noisy Discs: Sometimes disc emits srek Mio-srek followed sluggish spinning wheel. This is due to the shear plate with the brake disc. Orsinya half of the brake caliper piston side fouled plate. This causes the wedge half puck tilt brake boost due to the extent of the uneven piston calipers guns, long lining thickness will be different and so will shift the slope puck disc lining up srek-srek wheezes. TIPS: just went quite simple really, the easiest to remove the plate pengganjalnya so that the surface of her pieces flat plate. But you have to re-tune kalipernya pull the brake lever so that it is not too deep. If guns want to be bothered, wrote pengganjalnya fill with additional help glue a thin plate bonded iron.
No comments:
Post a Comment